CH600/740
Product Name
LATHE
Product Content
‧The high precision spindle is ground , hardened and supported by Ihree bearings ( Two taper roller bearings and one ball bearing )
‧104mm ( 4 1/11 " ) spindle bore Dl-11 nose
‧Magnetic multiple-disc clutches are used for efficient starting and reversing the spindle
‧Rapld and positive magnetic brake interconnected with main clutcher operated by enlergency switch or foot control
‧All running parts are lubricated by a pressuro pump in gear box
‧Sliding , surfaclng and screw 一cutting motlons are fully interlocked in apron
‧A cone-clutch device in the apron to prevent overload
‧Induction hardened and precision ground bedway 15 rnade of high tensiorl cast iron FC 30
‧A dual feed rate by means of a reduction gear system ( ratlol：1 , 1：1/4 ) in thetallstock , provides easy operation for drilling
| STANDARD ACCESSORIES ................................................................................ |
OPTIONAL ACCESSORIES .......................................................................................................... |
|
Main drive motor 15HP
M . T . NO . 5 dead Center Coolant system Change gears for module & D.P cutting Tool box with tool kits |
Steady rest Face plate Follow rest 3 jaw scoll chuck 4 jaw scoll chuck Drive plate |
| SPECIFICATIONS |
600(24") |
740 (29") | |
| General Capacity |
Center height |
300mm (11-7/8") | 370mm (14-3/4") |
| Swing over bed |
600mm (23-5/8") | 740mm (29-1/8") | |
| Swing over gap |
820mm (32-1/4") | 960mm (37-25/32") | |
| Swing over cross slide |
380mm (15") | 520mm (20-1/2") | |
| Distance between centers |
1.35m (53.1"), 1.84m(72.4"), 2.91m(114.5"), 3.96m(156') | ||
| Main Spindle |
Spindle nose |
ASA D1-11 | |
| Spindle bore diameter | 104mm (4-1/11") | ||
| Taper of spindle bore |
108X1:20 | ||
| Taper of center | MT5 | ||
| Spindle speeds | 25~1,200 rpm (12 steps) | ||
| Carriage | Cross slide travel |
330mm (13") | 465mm (18-1/4") |
| Compound rest travel | 230mm (9") | ||
| Max. size cutting tool | 25 X 25mm (1"X1") | ||
| Tailstock | Spindle diameter | 77mm (3-1/32") | |
| Spindle travel | 178mm (7") | ||
| Taper of center | MT5 | ||
| Bed | Bed length | 2,590/3,090/4,160/5,210mm (102"/122"/164"205") | |
| Bed width | 420mm(16-1/2") | ||
| Threading &Feeding |
System | 515mm(20-1/4") | |
| Pitch of leadscrew | Ø38mm(1-1/2") 4TPI or 6mm/pitch | ||
| Metric pitch | 0.5~14 mmX31 kinds | ||
| Inch pitch threads | 2~56 TPI X45 kinds | ||
| Module pitch threads | 0.25~7 M.P.X 23 kinds | ||
| Diametral pitch threads | 4~112 D.P.X 43 kinds) | ||
| Range of longitudinal feeds | 0.03~0.73 mm/rev.(0.0012-0.0287"/rev.) | ||
| Range of cross feeds | 0.01~0.3 mm/rev.(0.0004~0.0118"/rev.) | ||
| Power | Main drive motor | 15 HP (11.25kw) or 10HP (7.5kw) | |
| Rapod traverse motor | 1/2HP | ||
| Coolant pump motor | 1/8 HP | ||
| Net weight (CH-600) | 3,550/3,750/4,350/4,750 kgs (7,150/7,810/8,690/9,570 lbs) | ||
| Gross weight | 3,750/3,950/4,550/5,000 kgs(8,250/8,690/10,010/11,000 lbs) | ||
| Packing size approx. ( L X W X H ) |
3,035/3,520/4,600/5,590X1,270X1,880mm (119.5"/138.5"/181.3"/220"X50X74") |
||
※Specificationd are subject to change without notice for further design improvement。
